Beacon Morris Garage Heater Troubleshooting

Beacon Morris Garage Heater Troubleshooting

Garage heaters are not always a matter of concern. Hence getting help on issues regarding garage heaters can be difficult. 

Wondering about beacon Morris garage heater troubleshooting?

Beacon Morris garage heaters may have problems with their thermostat which can be solved by working on the thermostat or the heating element. The problem with two flashes can be solved by cleaning or replacing the high-limit switch. Igniter issues can be fixed by cleaning or replacing them.  

All the details can be found regarding the matter in this article. 

Beacon Morris Garage Heater Troubleshooting

beacon morris garage heater problems

Source: globalindustrial.ca

A few different beacon morris garage heater problems are common. Each has its own unique solution.

Problem 1: Thermostat problems

The thermostat is one of the main beacon Morris garage heater parts. It is possible for the heater to turn on and off at the wrong times or not reach the desired temperature when the thermostate is not accurately functioning. Also, the thermostat may not turn the heater on or off at all, resulting in the heater running continuously.

Solution: 

Since, the thermostat problem in a heater refers to an issue with the device that controls the temperature of the heater, so the problems need to be addressed as soon as possible. Let’s get to know what needs to be done to get over the situation.   

Tools needed:

  • User’s manual
  • Multimeter
  • Screwdriver
  • Ohmmeter

Step 1: Check the wiring

Checking the wiring should be your first order of business. To accomplish this, start by shutting off the power supplied to the heater.

The wiring diagram should then be located. it should be on a label that is attached to the heater.

Check to see that the wiring is done correctly and corresponds to the diagram.

Check the connectors of the wiring to see if any of the wires are damaged or loose. Use a multimeter to check the integrity of the wire. It is necessary to do this to guarantee that the heater receives the appropriate voltage.

Step 2: Replace the batteries

If the wiring appears alright, the batteries in the Beacon Morris garage heater may need to be replaced.

Find the chamber that houses the batteries on the control device for the heater first. After that, take out the old batteries and dispose of them in the appropriate manner.

Now put the fresh batteries in place. Be certain that the positive and negative ends are correctly matched up.

Put the cover back on the battery compartment. After that, put the heater through its paces to ensure that it is operating well.

Step 3: Calibrate the thermostat

After the power has been turned off, remove the cover from the thermostat in order to gain access to it. Find the dial or potentiometer that is used for calibration.

Make the necessary adjustments to the calibration dial or potentiometer. Do this by using a screwdriver or another similarly sized tool. Continue calibrating until the display of the thermostat reaches the temperature that you want.

Replace the cover on the thermostat control unit after you have completed calibrating it. Test the effectiveness of the heater after you have restarted the power supply to it. Check to see if it is reaching the desired temperature while it heats up.

Note that calibrating the thermostat does not affect the boiler pressure of the heater. 

Step 4: Check the heating element

Check to see that the heater is not receiving any power from the electrical outlet.

The next step is to find the heating element that is housed within the heater unit. Take a reading of the resistance of the heating element using either an ohmmeter or a multimeter.

To assess whether or not the heating element is operating correctly, compare the reading of the resistance. Check how closely the resistance matches the specifications provided by the manufacturer. If the heating element has become defective, a new one will have to be installed.

To have the heating element in the heater replaced, you need to take it to a professional. It is not suggested that you carry it out by yourself.

Problem 2: Two Flashes 

Beacon morris garage heater 2 flashes is another common problem. There are typically two flashes on a heater when there is a fault or error code. The heater may display two flashes if the sensor that measures the room temperature is faulty or disconnected. 

Moreover, fresh air may be blocked from entering the heater, which results in two flashes.

Solution: 

Usually cleaning the heater resolves the problem maximum time. The rest of the time requires to change the high-limit switch. In order to diagnose and resolve the issue, follow the guidelines below. 

Tools needed:

  • User’s Manual
  • Anemometer 
  • Compressed air
  • Soap and water
  • Screwdriver

Step 1: Check the airflow 

Turn on the heater. Then take readings with a hand-held anemometer to determine how much air is passing through the vents in the exhaust system. 

Check the reading for the airflow against the criteria specified by the manufacturer. After that, check to see if the airflow is within the typical range.

The airflow may be obstructed or not within normal range. In that case, the cause of the anomaly should be addressed.

If there is any smell of kerosene from the propane heater, the issue lies somewhere else. And it must be addressed as soon as possible. 

Step 2: Clean the heater’s air intake vents

Turn off the electricity to the heater by removing it from its connection to the electrical source.

Remove any dirt or dust carefully by using a gentle brush or a vacuum cleaner. Clear out as much of the accumulated dirt built up on or around the air intake vents as you can.

Make use of compressed air to clear away any debris that may still be stuck within the air intake vents.

After the vents have been thoroughly cleaned, the air intake vents have to be reinstalled. 

Step 3: Clean the heater’s air filters

Find where the air filters are located. In most cases, the air filters for a Beacon Morris garage heater may be found within the heater itself.

The position of the heater’s air filters may be different from one model to another. They might be found in the air intake vents. Or in a separate compartment placed somewhere within the heating unit itself.

Refer to the instructions provided by the manufacturer for your particular type of heater. This will give you more precise information on the positioning of the air filters.

After you have found the filters, take the air filters out of the unit.

Before replacing the filters, you should give them enough time to thoroughly dry out.

Once cleaned and dried, replace the air filters. Turn the power back on and test if the two flashes are still present. 

Step 4: Replace the high-limit switch

If you are still seeing the two flashes, the issue may lie in a different area.

Take off the screws that hold the electrical connections to the switch. After that, remove any screws or other fasteners that are securing the switch in place.

When installing the new high-limit switch, be sure to secure it into place first. Then you should connect all of the wirings.

To ensure that the heater is functioning properly, switch the power supply back on. Check to see whether the button on the switch is working correctly.

With the switch installed properly, the problem will be resolved. 

If you are looking for a new high-limit switch, we recommend the Beacon Morris J11R00306-002 High Limit Switch.

Problem 3: Igniter Problems 

The igniter is a critical component in heating systems, that includes  furnaces and boilers. Ignite problems with beacon morris garage heater igniter occur every so often. And there might be a few different reasons why a propane heater may not ignite.

Solution: 

The precise cause of the problem must be found and then solved accordingly. 

Tools needed:

  • User’s manual.
  • Multimeter
  • Compressed air
  • Screwdriver
  • Wire brush or sandpaper

Step 1: Check the wiring

We already discussed how to check the wiring in the thermostat problem section. Check out that segment. 

Step 2: Replace the batteries

The process of replacing the batteries was also in the thermostat problem section. Check out that part for details. 

Step 3: Clean the ignition system

If the wiring and battery are alright, the problem might be with the ignition system itself. 

Turn off the heater’s electricity. Find the ignition system of the heater. It is usually located close to the burners.

Clear away any accumulation of debris or dirt that may have occurred around the ignition system components. In order to clean any accumulation of carbon on the spark plug, clean it with a wire brush or sandpaper. Make use of compressed air to blast any debris out of the components of the ignition system.

Put the ignition system back together again. In order to ensure that everything is working as it should reactivate the heater.

Step 4: Replace the igniter

It’s possible that cleansing the system won’t solve the issue in certain cases. And it’s possible that the igniter itself has to be changed.

To do this, the heater must be turned off once again, and the igniter must be located.

Take apart the old igniter and disconnect the wires from it. By using a screwdriver, you have to remove any screws or other fasteners that are keeping the old igniter in place.

The replacement igniter may be installed by simply fastening it into position. Then make sure to connect the wire in accordance with the instructions provided by the manufacturer.

Conduct a test on the heater by turning it on. Then ensure that the igniter is operating as it should.

Step 5: Check the fuel supply

Sometimes the issue may be traced back to the fuel supply that is being used by the heater. In order to complete the diagnostic, the heater has to be switched off.

Find the fuel supply, and inspect it carefully for any obvious cracks or leaks. In addition, check to see that the fuel tank is full. Or the heater must at least have enough fuel for it to operate.

Examine the fuel filter to see if it has become clogged. If the filter is clogged, you should clean the filter. If there is any damage to the filter, it will need to be changed.

Turning the power back on will allow you to check that the fuel pump is operating as it should. After that, have a look at the flow of fuel.

It is possible that the fuel pump has to be changed. That is if there is no flow of fuel or if it is not operating properly. See a technician about having the fuel pump changed. It is not something that we suggest you undertake on your own.

Frequently Asked Questions (FAQs):

How do you test a heater igniter?

To test a heater igniter, turn off the heater, find the igniter, unhook the wires, and use an ohmmeter to test it. If the resistance matches the manufacturer’s specs, apply voltage to the igniter and watch for a spark. The igniter is faulty if the resistance is too high or there is no spark.

What causes an igniter to fail?

An igniter can fail due to several reasons such as overheating from continuous use, wear and tear over time, dirty or clogged burners that restrict gas flow, voltage surges or power outages that damage the electronics, improper connections that put stress on the igniter, or a manufacturer defect.

Can you clean igniters?

Yes, igniters can be cleaned. The procedure involves removing any debris or dirt buildup around the components of the ignition system, cleaning the spark plug with a wire brush or sandpaper to remove any carbon buildup, and using compressed air to blow out any debris from the ignition components.

Conclusion

That concludes what we had to say about beacon morris garage heater troubleshooting.

If your troubles persist, we recommend going to a technician. 

Good luck!


Share post on

Leave a Reply

Your email address will not be published. Required fields are marked *


BESTHEATERGUIDE.COM is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

What Is The Right Boiler Pressure? Mathematically Explained! Patio Heater Info

What Is The Right Boiler Pressure? Mathematically Explained!

The boiler pressure should be adjusted automatically as you turn on the boiler system....

By Rubby Vans
Heat Trap vs Check Valve [Multi-Featured Comparisons] Patio Heater Info

Heat Trap vs Check Valve [Multi-Featured Comparisons]

Heat trap and check valve are two prevalent methods to avoid heat dissipation in...

By Rubby Vans
Does A Tankless Water Heater Need A GFCI Breaker? [Answered] Patio Heater Info

Does A Tankless Water Heater Need A GFCI Breaker? [Answered]

With the rising energy cost, more people rely on tankless water heaters to meet...

By Rubby Vans
8 Reasons & Solutions Why Propane Heater Flares Up! Patio Heater Info

8 Reasons & Solutions Why Propane Heater Flares Up!

Propane heaters are widely used in households. They are popular for their services. But...

By Rubby Vans
The Toe Kick Heater Not Blowing Properly Patio Heater Info

The Toe Kick Heater Not Blowing Properly

Some people do not like having their feet cold at all. For them, toe...

By Rubby Vans
Taco Zone Valve Stuck Open [Reasons and Solutions!] Patio Heater Info

Taco Zone Valve Stuck Open [Reasons and Solutions!]

Taco Zone Valves are known for their reliable operation, but even the system can...

By Rubby Vans
Propane Heater Smells Like Kerosene [Everything You Need to Know!] Patio Heater Info

Propane Heater Smells Like Kerosene [Everything You Need to Know!]

Propane heaters are a common choice for people who want to heat their homes....

By Rubby Vans
Warm Morning Gas Heater troubleshooting: 8 Problems & Solutions Patio Heater Info

Warm Morning Gas Heater troubleshooting: 8 Problems & Solutions

Despite handling with care, Warm Morning Gas Heaters sometimes malfunction. And this can happen...

By Rubby Vans

Latest Posts

Primary/Secondary Limit Switch Open Lennox – Causes & Troubleshooting! Tankless heater info

Primary/Secondary Limit Switch Open Lennox – Causes & Troubleshooting!

It’s cold and chilly outside and you suddenly notice that you have no heat...

By Rubby Vans
Limit Or Rollout Switch Open – Causes and Solutions! Tankless heater info

Limit Or Rollout Switch Open – Causes and Solutions!

The gas furnace’s limit or rollout switch opens for several reasons. I have faced...

By Rubby Vans
Mini Split Compressor In Crawl Space Is It A Viable Option? Tankless heater info

Mini Split Compressor In Crawl Space Is It A Viable Option?

Mini split compressors in crawl space is a tempting idea. To ensure efficient performance,...

By Rubby Vans
What Does DHW Wait Mean In a Navien Water Heater? Tankless heater info

What Does DHW Wait Mean In a Navien Water Heater?

Navien water heaters have some really useful features that make them very popular. One...

By Rubby Vans
Second Stage Heating Not Working: Reasons and Solutions! Tankless heater info

Second Stage Heating Not Working: Reasons and Solutions!

Having a well working heating system is essential for staying warm and comfortable on...

By Rubby Vans
Taco Zone Valve Control Indicator Lights Meaning Tankless heater info

Taco Zone Valve Control Indicator Lights Meaning

Taco zone valve control indicator lights mean power availability, need for heat and the...

By Rubby Vans
Taco SR Series Troubleshooting: Complete Guide Tankless heater info

Taco SR Series Troubleshooting: Complete Guide

The Taco SR series is a reliable and efficient switching relay for your HVAC...

By Rubby Vans
How Long Do Propress Fittings Last? Mystery Solved! Tankless heater info

How Long Do Propress Fittings Last? Mystery Solved!

For easy and convenient installment, many homeowners are interested in Propress instead of classic...

By Rubby Vans